| Bore | 3.54in |
|---|---|
| Displacement | 171in³ |
| Engine Model | Cat C2.8* |
| Maximum Engine Speed | 2550 rpm |
| Maximum Gross Power | 74.7hp |
| Maximum Gross Power - ISO 14396 | 74.3hp |
| Maximum Gross Power - ISO 14396 (metric) | 75.3mhp |
| Maximum Gross Power - Rated Engine Speed | 2400r/min |
| Maximum Gross Power - SAE J1995 | 74.7hp |
| Maximum Gross Torque - ISO 14396 | 221lb/ft |
| Maximum Gross Torque - SAE J1995 | 222lb/ft |
| Maximum Net Torque - ISO 9249 | 217lb/ft |
| Maximum Net Torque - SAE J1349 | 218lb/ft |
| Note | Advertised power is tested per the specified standard in effect at the time of manufacture. |
| Note (1) | Net power advertised is the power available at the flywheel. |
| Note (2) | *Two Cat C2.8 engine emission options are available: 1) Meets U.S. EPA Tier 4 Final, EU Stage V. 2) U.S. EPA Tier 3 and EU Stage IIIA equivalent. Tier 3 engine specs are 0.3 kW/0.4 hp more gross power (SAE J1995), 0.2 kW/0.3 hp on net power (SAE J1349) an |
| Note (3) | #Maximum gross and net torque measured at 1,600 rpm. |
| Rated Net Power - 2,400 rpm - ISO 9249 (metric) | 73.1mhp |
| Rated Net Power - ISO 9249 | 72.1hp |
| Rated Net Power - Rated Engine Speed | 2400r/min |
| Rated Net Power - SAE J1349 | 72.7hp |
| Stroke | 4.33in |
| Operating Weight | 12628lb |
|---|
| Bucket Capacities | 0.75-1.55 m³ (1.0-2.0 yd³) |
|---|---|
| Bucket Capacities - General Purpose | 0.80-1.35 m³ (1.0-1.7 yd³) |
| Bucket Capacities - Light Material | 1.25-1.55 m³ (1.6-2.0 yd³) |
| Multi-Purpose | 0.75-1.1 m³ (1.0-1.4 yd³) |
| Note | Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration. |
| Note (1) | Bucket capacities stated include BOCE, in line with ISO 7546. |
| Recyclability | 93% |
|---|
| Axles - Front Center Differential | 2.3Gal |
|---|---|
| Axles - Rear Center Differential | 2.3Gal |
| Cooling System | 3.2Gal |
| Engine Crankcase | 2.3Gal |
| Fuel Tank | 18.5Gal |
| Hydraulic System - Including Tank | 17.8Gal |
| Hydraulic Tank | 11.8Gal |
| Note | No Diesel Exhaust Fluid (DEF) fluid needed on this size engine. |
| Transmission | 0.6Gal |
| Front | Fixed (standard) Locking Differential (optional) |
|---|---|
| Note | Oscillation of ±11 degrees via hitch between front and rear frames. |
| Rear | Fixed (standard) Locking Differential (optional) |
| Maximum Flow - Steering Pump | 12.3gpm |
|---|---|
| Maximum Working Pressure - Steering Pump | 3336psi |
| Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.25 turns or 4.00 turns |
| Steering Articulation Angle - Each Direction | 39° |
| Steering Cycle Times – (full left to full right) – at High Idle | 2.8s |
| Forward and Reverse - Speed Range 1* | 6mile/h |
|---|---|
| Forward and Reverse - Speed Range 2** - High Speed | 10.5mile/h |
| Forward and Reverse - Speed Range 2** - Standard | 12mile/h |
| Forward and Reverse - Speed Range 3*** | 25mile/h |
| Forward and Reverse - Speed Range Creep# | 6mile/h |
| Note | #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph). |
| Note (1) | *Creep function not available in this gear or above. |
| Note (2) | **Max speed dependent on model and configuration (standard vs. high speed transmission). |
| Note (3) | ***Reverse is 30 km/h (19 mph). |
| Note | *This tire has been used for all dimension, stability and performance data. |
|---|---|
| Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
| Note (2) | In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities. |
| Note (3) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
| Tire Size - Optional | 405/70 R18 Powerloads |
| Tire Size - Optional (1) | 340/80 R18 XMCL/Bibload |
| Tire Size - Optional (2) | 340/80 R18 TRI 2 |
| Tire Size - Optional (3) | 40X14-20 TL, SM/TR |
| Tire Size - Optional 4 | 340/80 R18 Duraforce |
| Tire Size - Standard | *405/70 R18 SPT9 |
| FOPS | ISO 3449:2005 Level II |
|---|---|
| Note (1) | Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU. |
| ROPS | ISO 3471:2008 |
| Hydraulic Cycle Time - Dump | 1.6s |
|---|---|
| Hydraulic Cycle Time - Float Down | 2.8s |
| Hydraulic Cycle Time - Lift | 5s |
| Hydraulic Cycle Time - Rackback | 2.2s |
| Main Relief - 1st Auxiliary (3rd slice) | 3408psi |
| Main Relief - 1st Auxiliary (3rd slice) - High Flow* | 32gpm |
| Main Relief - 1st Auxiliary (3rd slice) - Standard Flow* | 21gpm |
| Main Relief - 2nd Auxiliary (4th slice) | 3408psi |
| Main Relief - 2nd Auxiliary (4th slice) - Flow | 12gpm |
| Note | * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display. |
| 80% of Tip: Firm and Level EN474-3 †† | 5211lb |
|---|---|
| Articulation Angle - Degrees | 39° |
| Carry Height: Bucket Pin | 1.08ft |
| Clearance: Bucket at 45° * | 8.25ft |
| Clearance: Level Bucket** | 9.92ft |
| Clearance: Load over Height** | 9.5ft |
| Departure Angle - Degrees | 30° |
| Dig Depth** | 0.33ft |
| Dump Angle at Full Lift | 45° |
| Height: Bucket Pin** | 10.67ft |
| Height: Ground Axle Center** | 1.58ft |
| Height: Ground Clearance** | 1ft |
| Height: Ground to Beacon** | 8.67ft |
| Height: Ground to Cab** | 8.08ft |
| Height: Overall** | 13.5ft |
| Length: Front Axle to Front of Coupler | 3.5ft |
| Length: Hitch to Front Axle | 3.58ft |
| Length: Overall* | 17.58ft |
| Length: Rear Axle to Bumper | 4.58ft |
| Length: Wheel Base | 7.08ft |
| Note (1) | *Vary with bucket |
| Note (2) | **Vary with tire |
| Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 0.95 m3 (1.2 yd3) general purpose bucket. |
| Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
| Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
| Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
| Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
| Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9EM 405/70 R18 tires and 0.95 m3 (1.2 yd3) general purpose bucket with bolt-on cutting edge or a class |
| Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9. |
| Operating Weight: Bucket ^ | 12632lb |
| Operating Weight: Carriage and Tines ^^ | 12240lb |
| Rack Angle at Carry | 51° |
| Rack Angle at Full Lift | 56° |
| Reach: Bucket at 45° * | 2.42ft |
| Tipping Load - Full Turn - ISO 14397-1 † | 8225lb |
| Tipping Load - Full Turn † | 6514lb |
| Tipping Load - Straight - ISO 14397-1 † | 9760lb |
| Tipping Load - Straight † | 7748lb |
| Turning Radius: Inside of Tires | 6.75ft |
| Turning Radius: Outside of Tires | 12.92ft |
| Turning Radius: Over Bucket | 14.17ft |
| Width: Bucket | 6.17ft |
| Width: Over Tires | 6.08ft |
| Width: Tread Center | 4.67ft |
| 80% of Tip: Firm and Level EN474-3 †† | 4970lb |
|---|---|
| Articulation Angle - Degrees | 39° |
| Carry Height: Bucket Pin | 1.17ft |
| Clearance - Bucket at 45° | 7.83ft |
| Clearance - Level Bucket | 9.92ft |
| Clearance: Load over Height** | 9.5ft |
| Departure Angle - Degrees | 30° |
| Dig Depth | 0.25ft |
| Dump Angle at Full Lift | 50° |
| Height - Bucket Pin | 10.67ft |
| Height - Ground Clearance | 1ft |
| Height - Ground to Cab | 8.08ft |
| Height: Ground Axle Center** | 1.58ft |
| Height: Ground to Beacon** | 8.67ft |
| Height: Overall** | 13.83ft |
| Length - Overall with Bucket | 18.17ft |
| Length - Wheel Base | 7.08ft |
| Length: Front Axle to Front of Coupler | 4.33ft |
| Length: Hitch to Front Axle | 3.58ft |
| Length: Rear Axle to Bumper | 4.58ft |
| Note (1) | *Vary with bucket |
| Note (2) | **Vary with tire |
| Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 0.95 m3 (1.2 yd3) general purpose bucket. |
| Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
| Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
| Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
| Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
| Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9EM 405/70 R18 tires and 0.95 m3 (1.2 yd3) general purpose bucket with bolt-on cutting edge or a class |
| Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9. |
| Operating Weight: Bucket ^ | 12863lb |
| Operating Weight: Carriage and Tines ^^ | 12434lb |
| Rack Angle at Carry | 46° |
| Rack Angle at Full Lift | 51° |
| Reach - Bucket at 45° | 2.67ft |
| Tipping Load - Full Turn † | 2818kg |
| Tipping Load - Straight † | 7359lb |
| Tipping Load – Full Turn – ISO 14397-1 † | 7220lb |
| Tipping Load – Straight – ISO 14397-1 † | 8613lb |
| Turning Radius - Inside Tire | 6.75ft |
| Turning Radius - Over Bucket | 14.67ft |
| Turning Radius: Outside of Tires | 12.92ft |
| Width - Bucket | 6.17ft |
| Width - Over Tires | 6.07ft |
| Width - Tread Center | 4.67ft |
