PM622 Cold Planer

Maximum Milling Depth	13in
Milling Width	88in
Number of Bits	185
Rotor Speeds	100 / 109 / 118 rpm

Engine	Cat C18
Maximum Milling Speed	328ft/min
Maximum Travel Speed	3.7mile/h
Rated Power	636HP

Operating Weight	74737lb
Transport Weight	66139lb

Conveyor Swing	60 degrees from center
Height - Canopy	13.29ft
Maximum Truck Clearance	15.94ft
Minimum Left Cutting Radius	6.56ft
Minimum Right Cutting Radius	5.91ft
Operating Length - Conveyor Up	47.64ft
Operating Width	10.2ft
Transport Height	9.84ft
Transport Length	40.78ft
Transport Width	8.89ft

Cooling System	22.5gal (US)
Diesel Exhaust Fluid (DEF) Tank	12.4gal (US)
Engine Oil	17.2gal (US)
Fuel Tank	292.7gal (US)
Hydraulic Tank	29.9gal (US)
Water Spray System Tank	898.2gal (US)

Standard Equipment:

Operator Environment
- Ground control keypads
- Single high-resolution LCD touchscreen display
- 12-volt power receptacle
Cat Connect Technology
- Cat Product Link
- Cat GRADE
Conveyor
- Grease tensioner
- Material removal boost feature
Rotor System
- Automatic plunge-cut
- Automatic transition feature
- Obstacle jump
- Three cutting speeds
Powertrain
- Auto engine idle control
- High capacity cooling system
- Dual propel pumps
- Automatic load control
Hydraulic System
- Dual pump hydraulic propel system
- Traction control
Service And Maintenance
- Sampling ports for Scheduled Oil Sampling (S·O·S℠)
- Power hood
- Platform-level engine oil dipsticks
- Rotor chamber water spray system
- Air compressor
- Accessory drive system
- 3400 L (898 gal) onboard water tank
- Side water fill valve
Safety And Security
- Platform handrails
- Signaling/warning horn
- Wide-dispersion LED work lights

Optional Equipment:

Operator Environment
- Dual high-resolution LCD touchscreen displays
- Hydraulically folding canopy with LEDs
- Air-ride suspension seats
- Windscreens
Cat Connect Technology
- Inboard ski
- Sonic sensor (averaging or string line)
- Ground level grade controls and displays
Conveyor
- Dust abatement system
- Remote camera (loading conveyor)
Rotor System
- System K Rotor - Course (25 mm)
- System K Rotor - Course (18 mm)
- System K Rotor - Standard (15 mm)
- System K Rotor - Fine (10 mm)
- System K Rotor - Fine (8 mm)
- System K Rotor - Micro (6 mm)
- System H Rotor - Micro (6x2 mm)
- Diamond bits
- Bit bucket trays
- Pneumatic bit removal tool
- Tool holder extractor
- Rotor turning device with pendant control
Powertrain
- CE certificate
Hydraulic System
- Water tank transfer pump
- Fuel transfer pump
Service And Maintenance
- High pressure washdown
- Low pressure washdown
- Additional spray bars
Safety And Security
- Perimeter LED strip lights
- Magnetic LED work light
- Warning beacon (fixed or magnetic mount)
- Truck signal lights
- Remote camera (rear, front, magnetic mount)

Gregory Poole Equipment Company

3.9

Based on 46 reviews

review us on

Renee Herndon

21:55 29 Feb 24

Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.

Michael Birren

14:58 24 Feb 24

I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.

13:04 22 Feb 24

22:00 18 Feb 24

01:17 16 Feb 24

15:26 23 Sep 23

OLEKSANDR “Alex” Kovalenko

14:27 18 Sep 23

👍

Hunter Elliott

16:17 07 Sep 23

Rick Kelly-Crapse

21:06 25 Aug 23

They had all my parts for my 3208 Cat.Friendly folks at parts counter.

New PM622 Cold Planer in North Carolina

Standard Equipment:

Optional Equipment:

Contact Us Today

Standard Equipment:

Optional Equipment:

Cat® Grade Connectivity

Related Models

PM825 Cold Planer

PM620 Cold Planer

PM820 Cold Planer

PM822 Cold Planer

Contact Us Today