PM620 Cold Planer

Back to Home

The PM620 is a high-production, half-lane milling machine with a cutting width of 2010 mm (79.1 in) that performs controlled full-depth removal of asphalt and concrete pavements in a single pass.

Request a quote
Maximum Milling Depth 13in
Milling Width 79.1in
Number of Bits 178
Rotor Speeds 100 / 109 / 118 rpm
Engine Cat C18
Maximum Milling Speed 328ft/min
Maximum Travel Speed 3.7mile/h
Rated Power 636HP
Operating Weight 73480lb
Transport Weight 64882lb
Conveyor Swing 60 degrees from center
Height - Canopy 13.29ft
Maximum Truck Clearance 15.94ft
Minimum Left Cutting Radius 6.56ft
Minimum Right Cutting Radius 6.56ft
Operating Length - Conveyor Up 47.64ft
Operating Width 10.2ft
Transport Height 9.84ft
Transport Length 40.78ft
Transport Width 8.14ft
Cooling System 22.5gal (US)
Diesel Exhaust Fluid (DEF) Tank 12.4gal (US)
Engine Oil 17.2gal (US)
Fuel Tank 292.7gal (US)
Hydraulic Tank 29.9gal (US)
Water Spray System Tank 898.2gal (US)

Standard Equipment:

  • Operator Environment
    • Ground control keypads
    • Single high-resolution LCD touchscreen display
    • 12-volt power receptacle
  • Conveyor
    • Grease tensioner
    • Material removal boost feature
  • Cat Connect Technology
    • Remote troubleshoot capability
    • Cat Product Link
    • Cat GRADE
  • Rotor System
    • Automatic plunge-cut
    • Automatic transition feature
    • Obstacle jump
    • Three cutting speeds
  • Powertrain
    • Auto engine idle control
    • High capacity cooling system
    • Dual propel pumps
    • Automatic load control
  • Hydraulic System
    • Dual pump hydraulic propel system
    • Traction control
  • Service And Maintenance
    • Sampling ports for Scheduled Oil Sampling (S·O·S℠)
    • Power hood
    • Platform-level engine oil dipsticks
    • Rotor chamber water spray system
    • Air compressor
    • Accessory drive system
    • 3400 L (898 gal) onboard water tank
    • Side water fill valve
  • Safety And Security
    • Platform handrails
    • Signaling/warning horn
    • Wide-dispersion LED work lights

Optional Equipment:

  • Operator Environment
    • Dual high-resolution LCD touchscreen displays
    • Hydraulically folding canopy with LEDs
    • Air-ride suspension seats
    • Windscreens
  • Cat Connect Technology
    • Inboard ski
    • Sonic sensor (averaging or string line)
    • Ground level grade controls and displays
  • Conveyor
    • Dust abatement system
    • Remote camera (loading conveyor)
  • Rotor System
    • System K Rotor - Course (25 mm)
    • System K Rotor - Course (18 mm)
    • System K Rotor - Standard (15 mm)
    • System K Rotor - Fine (8 mm)
    • System K Rotor - Micro (6 mm)
    • System H Rotor - Micro (6x2 mm)
    • Diamond bits
    • Bit bucket trays
    • Pneumatic bit removal tool
    • Tool holder extractor
    • Rotor turning device with pendant control
  • Powertrain
    • CE certificate
  • Hydraulic System
    • Water tank transfer pump
    • Fuel transfer pump
  • Service And Maintenance
    • High pressure washdown
    • Low pressure washdown
    • Additional spray bars
    • Remote Flash
  • Safety And Security
    • Perimeter LED strip lights
    • Magnetic LED work light
    • Warning beacon (fixed or magnetic mount)
    • Truck signal lights
    • Remote camera (rear, front, magnetic mount)
Renee HerndonRenee Herndon
21:55 29 Feb 24
Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.
Michael BirrenMichael Birren
14:58 24 Feb 24
I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.
David LawrenceDavid Lawrence
13:04 22 Feb 24
Brandon PierceBrandon Pierce
22:00 18 Feb 24
Darin NoeDarin Noe
01:17 16 Feb 24
Jose SotoJose Soto
15:26 23 Sep 23
Hunter ElliottHunter Elliott
16:17 07 Sep 23
Rick Kelly-CrapseRick Kelly-Crapse
21:06 25 Aug 23
They had all my parts for my 3208 Cat.Friendly folks at parts counter.
js_loader