Cat?� C2.8 Industrial Power Unit

Maximum Power	74HP
Maximum Torque	221lb-ft @ 1600 rpm
Minimum Power	74HP
Rated Speed	2200-2400 rpm

Emissions	EU Stage V/U.S. EPA Tier 4 Final/ Japan 2014 (Tier 4 Final)

Aftertreatment	DOC+DPF
Aspiration	Turbocharged
Bore	3.54in
Combustion System	Direct injection
Compression Ratio	17.0:1
Cooling System	Liquid
Cycle	4 stroke
Displacement	170.9in³
Number of Cylinders	4 inline
Rotation from Flywheel End	Anti-clockwise
Stroke	4.33in

Dry Weight	1126lb
Height	38in
Length	46.9in
Width	31.9in

Note 1	*Final dimensions dependent on selected options

Standard Equipment:

Aftertreatment Equipment
- Aftertreatment mounted on engine as standard
Air System
- Standard and heavy duty air cleaners
Cooling System
- 50:50 water glycol mix
- Detailed guidance on cooling system design and validation available to ensure machine reliability
- Engine mounted radiator with top tank temperature of 108°C (226°F)
- Pusher or puller fan options
- Radiator erosion screen is available
Electrical And Electronics
- 12V system
- Data interface via CANbus J1939
- Instrument control panel available
- Full electronic control
- Glow plugs for best cold starting with minimum battery impact
- High power alternator and starter motor options
- Sensors and robust wiring harness included
Flywheel And Flywheel Housing
- SAE3 flywheel housing and flywheel with pilot bore
- Wide choice of interfaces for common transmissions and hydraulic pumps
Fuel System
- Electronic high pressure common rail
- Fuel filter - IOPU mounted
- Standard and heavy duty fuel filtration
- Water sensor included - early warning for operator
General
- Cold-start capable with standard equipment to -25°C
- Supplied painted or lacquered
Oil System
- Oil filters - mounting options available on either side of the engine, plus remote
- Dipsticks - choice of position and length
- High incline sump. 35° continuous in all directions. Suitable for machines that are used on steep slopes
Power Take-off (pto)
- SAE-A and SAE-B interfaces available

Optional Equipment:

Gregory Poole Equipment Company

3.9

Based on 46 reviews

review us on

Renee Herndon

21:55 29 Feb 24

Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.

Michael Birren

14:58 24 Feb 24

I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.

13:04 22 Feb 24

22:00 18 Feb 24

01:17 16 Feb 24

15:26 23 Sep 23

OLEKSANDR “Alex” Kovalenko

14:27 18 Sep 23

👍

Hunter Elliott

16:17 07 Sep 23

Rick Kelly-Crapse

21:06 25 Aug 23

They had all my parts for my 3208 Cat.Friendly folks at parts counter.

Standard Equipment:

Optional Equipment:

Cat?� C3.6 Industrial Power Unit

Contact Us Today