Cat?� C32 Industrial Power Unit

The Cat^?� C32 Industrial Power Unit is offered with a ratings of 746 bkW (1000 bhp) @ 1800 rpm. This rating meets U.S. EPA Tier 4 Final emission standards. Applications powered by C32 engines include: Bore/Drill Rigs, Chippers/Grinders, Construction, Cranes, Dredgers, Forestry, Hydraulic Power Units, General Industrial, Irrigation Equipment, Material Handling, Mobile Earthmoving Equipment, Paving Equipment, Pumps, Shovels/Draglines, Surface Hauling Equipment and Trenchers.

Pricing: Contact for Pricing

Request a quote

Photos
360 VIEWS

Pricing: Contact for Pricing

Request a quote

Maximum Power	1000HP
Maximum Torque	3825lb-ft @ 1200 rpm
Minimum Power	1000HP
Rated Speed	1800 rpm

Emissions	U.S. EPA Tier 4 Final and EU Stage V

Aftertreatment	DOC
Aspiration	Twin Turbocharged Aftercooled (TTA)
Bore	5.7in
Combustion System	Direct Injection
Compression Ratio	16.0:1
Cooling System	liquid
Cycle	4
Displacement	1958.9in³
Engine Configuration	V-12
Rotation from Flywheel End	Counterclockwise
Stroke	6.4in

Height	77.6in
Length	100.7in
Width	64.4in

Standard Equipment:

Air Inlet System
- Turbocharged
- Air-to-Air Aftercooled
Control System
- Electronic control system
- Over-foam wiring harness
- Automatic altitude compensation
- Power compensated for fuel temperature
- Configurable software features
- Engine monitoring system SAE J1939 broadcast and control
Cooling System
- Thermostats and housing, vertical outlet
- Jacket water pump, centrifugal
- Water pump, inlet
Exhaust System
- Exhaust manifold, dry
- Optional exhaust outlet
Flywheels And Flywheel Housing
- Choice of SAE No. 0 or SAE No. 1 flywheel housing
Fuel System
- MEUI injection
- Fuel filter, secondary (2 micron)
- Electronic fuel priming
Lube System
- Open crankcase ventilation system
- Oil cooler
- Oil filler
- Lube oil filter
- Rear sump oil pan
- Oil dipstick
- Gear driven oil pump

Optional Equipment:

Gregory Poole Equipment Company

3.9

Based on 46 reviews

review us on

Renee Herndon

21:55 29 Feb 24

Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.

Michael Birren

14:58 24 Feb 24

I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.

13:04 22 Feb 24

22:00 18 Feb 24

01:17 16 Feb 24

15:26 23 Sep 23

OLEKSANDR “Alex” Kovalenko

14:27 18 Sep 23

👍

Hunter Elliott

16:17 07 Sep 23

Rick Kelly-Crapse

21:06 25 Aug 23

They had all my parts for my 3208 Cat.Friendly folks at parts counter.

Contact Us Today

Get In Touch

Call: (800) 451-7278