TL943D Telehandler

Back to Home

The TL943D is precision engineered to handle any task, offering stability, maneuverability, speed and power in any application

Request a quote
Capacity at Maximum Height 7000lb
Capacity at Maximum Reach 1200lb
Drawbar Pull - Loaded 21582lbf
Frame Leveling 10°
Maximum Forward Reach 31ft
Maximum Lift Height 43ft
Rated Load Capacity 9000lb
Top Travel Speed 19mile/h
Turning Radius - Over Tires 12ft
Engine Model Cat® C3.4B
Gross Power - Basic 111HP
Note Meets U.S. EPA Tier 4 Final emission standards.
Operating Weight 25750lb
Optional (1) 13.00 × 24 Foam Duraforce
Optional (2) 14 × 24-16 PR Air
Optional (3) 14 × 24-12 PR Foam
Standard 370/75-28 Duraforce MT
Diesel Exhaust Fluid (DEF) Tank 5.7gal (US)
Fuel Tank 38gal (US)
Hydraulic System 47gal (US)
Auxiliary Hydraulic Flow 25gal/min
Auxiliary Hydraulic Pressure 3481psi
Note Auxiliary Hydraulic Circuit used for all attachments equipped with cylinders or other hydraulic components.
Pump Type Variable displacement load sensing axial piston pump
System Operating Pressure 3770psi
Boom Down 8.5s
Boom Up 9.9s
Tele In 14.6s
Tele Out 14.5s
Parking Brakes Wet disc, spring applied hydraulic release on front axle
Service Brakes Inboard wet disc brakes on front and rear axles
Types (1) Trunnion mounted planetary 55 degree steer axles.
Types (2) High bias limited slip differential on front axle.
Carriages - Dual Fork Positioning 50in
Carriages - Side Shift 48in
Carriages - Standard Rotate 50in
Carriages - Standard Tilt 50in
Carriages - Swing 100°, 1829 mm, 4028 kg Capacity, 2268 kg Swung (100°, 72 in, 9,000 lb Capacity, 5,000 lb Swung)
Carriages - Wide Rotate 72in
Carriages - Wide Tilt 72in
Cubing Forks [2] 1220 mm, 50 mm × 50 mm ([2] 48 in, 2 in × 2 in)
Hydraulic IT Coupler Includes Auxiliary Electrics
Lumber Forks - Option 1 [2] 1525 mm, 45 mm × 180 mm ([2] 60 in, 1.75 in × 7 in)
Lumber Forks - Option 2 [2] 1829 mm, 50 mm × 150 mm ([2] 72 in, 2 in × 6 in)
Pallet Forks - Option 1 [2] 1525 mm, 60 mm × 150 mm ([2] 60 in, 2.36 in × 6 in)
Pallet Forks - Option 2 [2] 1220 mm, 60 mm × 100 mm ([2] 48 in, 2.36 in × 4 in)
Pallet Forks - Option 3 [2] 1220 mm, 60 mm × 125 mm ([2] 48 in, 2.36 in × 5 in)
Forward 4 speed
Reverse 3 speed
Renee HerndonRenee Herndon
21:55 29 Feb 24
Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.
Michael BirrenMichael Birren
14:58 24 Feb 24
I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.
David LawrenceDavid Lawrence
13:04 22 Feb 24
Brandon PierceBrandon Pierce
22:00 18 Feb 24
Darin NoeDarin Noe
01:17 16 Feb 24
Jose SotoJose Soto
15:26 23 Sep 23
Hunter ElliottHunter Elliott
16:17 07 Sep 23
Rick Kelly-CrapseRick Kelly-Crapse
21:06 25 Aug 23
They had all my parts for my 3208 Cat.Friendly folks at parts counter.
js_loader