7295 Electric Rope Shovel

Back to Home

Cat® Electric Rope Shovels combine immense payload capability with low maintenance requirements and high reliability to deliver the lowest cost-per-ton loading solution for long-life mines. Our smallest rope shovel, the Cat 7295 has a payload of 45 tonnes (50 tons) — about half the payload of our flagship 7495. But like its larger counterpart, the 7295 features AC IGBT electrics for greater uptime, lower operating costs and faster cycle times. The 7295 is cleaner and more efficient than diesel-powered machines, plus its regenerative braking technology feeds electrical energy back to the grid.

Request a quote
Dipper Capacity 19.1-38.2 m3 (25-50 yd3)
Dipper Payload 50t
Note Dependent on application and material density.
Ballast - Furnished By Customer 352000lb
Note (1) These weights will vary slightly depending upon dipper and optional equipment selection.
Note (2) All specifications are based on a 19 m3 (25 yd3) dipper and standard 182.9 cm (72 in) treads.
Working Weight - With Dipper and Standard Links 1748837lb
Crawler Dimensions - Overall Width 182.9 cm (72 in) Treads, Standard 28.22in
Ground Bearing Pressure Ground bearing pressure is dependent upon many factors.
Ground Bearing Pressure - 182.9 cm (72 in) Treads 39in
Ground Bearing Pressure - Total Effective Bearing Area 315.6ft²
Hoist A motor coupled to two gear reductions drives a 137 cm (54 in) hoist drum.
Planetary Propel Dual-motor independent drive.
Swing Parallel shaft gear cases, driven by a vertically mounted motor, are located on either side of the revolving frame.
Upper Works Overall Width - Including Standard Walkways 41.33in
Cutting Height - Maximum 45ft
Cutting Radius - Maximum 67.59ft
Dumping Height - With Clearance to Open Dipper Door 27.56ft
Note (1) Optimal working ranges based on loading a Cat® 785D truck.
Note (2) *All specifications are based on a 19 m3 (25 yd3) dipper and standard 182.9 cm (72 in) treads.
Radius of Level Floor 48.88ft
Revolving Frame Tail Swing Radius 25.59in
Components (1) 6 pumps (4 for open gear lubricant and 2 for grease) located in an insulated, heated, double-walled lube room.
Components (2) External fast fill from lower level.
Type Automatic, single-line system for open gear lubricant and grease.
Drive IGBT Acutrol drive system.
Note Other voltages available to suit customer requirements.
Power Requirements - 50 Hz 6,000V, 6,600V, 7,200V
Power Requirements - 60 Hz 4,160V, 7,200V
Power Requirements - Average Power Demand 538-753 kW (721-1,010 hp)
Power Requirements - Peak power 2886HP
Power Requirements - Voltage 3 phase, 50/60 Hz, 7,200V
Components One piece, forged, seamless tubular dipper handle and wide-spread boom point sheaves equipped with hoist ropes and dipper padlocks to stabilize dipper handle.
Crowd Rope Crowd: the crowd machinery is located at the front center of the revolving frame; consisting of a motor, brake, drum and gearing. Plastic-impregnated crowd and retract ropes are used to move the dipper handle fore and aft.
Note High impact ropes available as an option
Standard Rope Data - Boom Suspension - Diameter 2.75in
Standard Rope Data - Boom Suspension - No. 4
Standard Rope Data - Crowd - Diameter 2.25in
Standard Rope Data - Crowd - No. 1
Standard Rope Data - Dipper Trip - Diameter 0.625in
Standard Rope Data - Dipper Trip - No. 1
Standard Rope Data - Hoist - Diameter 2.375in
Standard Rope Data - Hoist - No. 2
Standard Rope Data - Retract - Diameter 2.25in
Standard Rope Data - Retract - No. 1

Coming Soon

Renee HerndonRenee Herndon
21:55 29 Feb 24
Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.
Michael BirrenMichael Birren
14:58 24 Feb 24
I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.
David LawrenceDavid Lawrence
13:04 22 Feb 24
Brandon PierceBrandon Pierce
22:00 18 Feb 24
Darin NoeDarin Noe
01:17 16 Feb 24
Jose SotoJose Soto
15:26 23 Sep 23
Hunter ElliottHunter Elliott
16:17 07 Sep 23
Rick Kelly-CrapseRick Kelly-Crapse
21:06 25 Aug 23
They had all my parts for my 3208 Cat.Friendly folks at parts counter.
js_loader