DG200-2 (3 phase)

Displacement	864.71in
Emissions/Fuel Strategy	U.S. EPA Certified for Non-Emergency Application
Frequency	60 Hz
Fuel Type	Natural Gas
Natural Gas Rating	200 eKW
Speed	1800 rpm

Aspiration	Turbocharged-Aftercooled
Bore	5.31in
Compression Ratio	9.5:1
Engine Model	14.2 L, Inline 6, 4 Cycle, Spark - Ignited
Fuel System	Carburetor, Down Draft
Governor Type	Electronic
Stroke	6.5in

Height	67.37in
Length	127.95in
Weight	5756lb
Width	52.93in

Standard Equipment:

Closed coolant recovery system
Factory-installed radiator
50/50 Ethylene glycol antifreeze
Radiator and cooling fan complete with protective guards
Standard ambient temperatures up to 50°C (122°F)

Single element air filter

Primary and secondary fuel shut-off
Low fuel pressure switch
Fuel pressure test po
Natural Gas or LP Vapor
NPT connection
Dual lock off valves

Exhaust outlet with 3” pipe

Permanent magnet excitation
Full load capacity alternator
Class H insulation material
Permanent magnet excitation
Integrated Voltage Regulator
Matched to the performance and output characteristics of Cat engines
Class H insulation material
Full load capacity alternator
IP23 Protection

EMCP 4.2 Series generator set controller

Vibration isolaton (puck type)
Rubber vibration isolators

Battery charging alternator

Battery cables
Solenoid activated starter motor
Engine electrical system
Solenoid activated starter motor

Electronic governor (non adjustable)

EMCP 4.2 Series generator set controller

Batteries with rack and cables
12 volt starting motor

Optional Equipment:

Jacket water heater
Battery heater
Charging alternator
Battery charger – UL Listed 10 amp

Enclosures: sound attenuated, weather protective
Suitable for Use as Service Equipment (SUSE)
Automatic transfer switches (ATS)
UL 2200 package
CSA Certification

Thermal magnetic or electronic trip MCCBs
Anti-condensation heater
Shunt trip and auxiliary contact breaker
Anti-condensation heater
Excitation: [ ] Permanent Magnet Excited (PM)
Oversize and premium generators

What Our Customers Are Saying About Us

Gregory Poole Equipment Company

4.0

Based on 58 reviews

review us on

Tom Corona

1 month ago

Rich Stidd

2 months ago

Carlos Virgilio Sauceda Rivera

3 months ago

John Karpathian

5 months ago

Clean store and great employees

Hunter Flaugher

11 months ago

Hydraulic pump shop is unmatched. I made the mistake of going somewhere else before bringing my pump here. These guys were more than helpful and friendly. Went out of their way to help me find a solution for my problem even when it didn’t benefit them. This is how businesses should be run. I won’t go anywhere else.

Brian Hrudka

1 year ago

Too bad Poole Cat Field Service is better at invoicing than actually getting my machines moving.

A prompt and courteous technician arrived, and correctly diagnosed two problems with my mini Ex. Thank you. I corrected those problems, but machine still did not work.

He diagnosed a fuel problem as a clogged filter, rather than a bad fuel pump which I managed to diagnose. I also figured out, via help on the internet, that the fuel shut-off solenoid was bad.

Machine runs fine now. So my advice is to check the internet, before letting Poole charge you $870 for a two hour field visit. And you can find a perfectly fine aftermarket fuel pump for $20 rather than the $250 that Poole charges... and it arrives faster,

Jacey Price

2 years ago

Need to teach a tech how to drive a service truck. Around 2:48 on highway 40 east, the truck pictured (plate ending in 8236) flew across 3 lanes of traffic to meet the Cleveland rd exit. Almost hit a semi and caused me to swerve with my children in the car. Glad making the exit was more important than children’s lives.