EMCP 4.4 Master Control Panel

The EMCP 4.4 Master Control Panel is a wall mounted system that monitors and controls up to eight engine generators for operation in parallel with or without a single utility source.

Pricing: Contact for Pricing

Request a quote

Photos

The EMCP 4.4 Master Control Panel is a wall mounted system that monitors and controls up to eight engine generators for operation in parallel with or without a single utility source.

Pricing: Contact for Pricing

Request a quote

Application	LV and MV (208V - 38 kV)
Configuration	Remote monitoring and control for up to 8 generator sets via high-speed network. Enables paralleling a group of EMCP 4.4 equipped generator sets to a single utility source.
Modes of Operation	Emergency standby, island, utility paralleling

ANSI Protective Devices	15/25, 27/59, 81 O/U, 32, 40, 50, 51

ANSI Protective Devices	15/25. 27/59, 81 O/U, 32,47 (Industrial Grade)

Certifications	IBC, CBC, UBC & OSHPD Certified
Control Panel Enclosure	NEMA 1 wall-mounted construction
Low Voltage Standards	NEMA SG-5, CSA, ANSI C37.51, ANSI C37.20.1, UL 1558 or UL 891, NFPA 110, NFPA 99 and NFPA 70
Medium Voltage Standards	NEMA SG-5, ANSI / IEEE C37.20.2, CSA-C22.2 No. 31-M89, EEMAC G8-3.2, NFPA 70, NFPA 99 and NFPA 1110
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C to +60°C

Standard Equipment:

Configuration
- Wall mounted supervisory control system provides centralized monitoring and control of up to eight generators equipped with EMCP4.4 paralleling control panels
Application
- LV and MV (208V - 15 kV) 50/60Hz
Operating Temperature
- 0-50 C
Medium Voltage Standards
- UL 508A
Emergency Transfer Load Manager Standard Equipment
- Data Table Interface
- 19" Color Touchscreen

Optional Equipment:

Emergency Transfer Load Manager Optional Equipment
- Utility Monitoring and Circuit Breaker Control I/O provided in XLM version of Master Control Panel provided in XLM version of Master Control Panel
Related Products - Attachments
- Diesel Generator Sets - C9, C13, C15, C18, C27, C32, 3500, C175

Gregory Poole Equipment Company

3.9

Based on 46 reviews

review us on

Renee Herndon

21:55 29 Feb 24

Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.

Michael Birren

14:58 24 Feb 24

I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.

13:04 22 Feb 24

22:00 18 Feb 24

01:17 16 Feb 24

15:26 23 Sep 23

OLEKSANDR “Alex” Kovalenko

14:27 18 Sep 23

👍

Hunter Elliott

16:17 07 Sep 23

Rick Kelly-Crapse

21:06 25 Aug 23

They had all my parts for my 3208 Cat.Friendly folks at parts counter.

Contact Us Today

Get In Touch

Call: (800) 451-7278