C1.1 Generator Set

Duty Cycle	Standby, Prime
Emissions/Fuel Strategy	R96/EUIIIa Equivalent
Frequency	60 Hz
Maximum Rating	8.8 ekW
Minimum Rating	8.0 ekW
Speed	1800 rpm
Voltage	110 to 480 Volts

Aspiration	Naturally Aspirated
Bore	3in
Compression Ratio	23.0:1
Displacement	69in³
Engine Model	C1.1, In-line 4, 4-cycle diesel
Fuel System	Indirect Injection
Governor Type	Mechanical
Stroke	3.2in

Height - Maximum	39.2in
Length - Maximum	55.1in
Width - Maximum	24.4in

Standard Equipment:

Air cleaner; light duty with disposable element

GCCP 1.3

Coolant drain line with valve
Caterpillar extended life coolant
Radiator and cooling fan with guards
Fan drive, battery charging alternator drive

Stub pipe, gaskets, raincap & SAE exhaust flange for customer use - shipped loose

Base, formed steel with single wall integral 8-hour fuel tank
Standard open set fuel tank/base supplied

12 Leads
IP23 Protection
Segregated low voltage (AC/DC) wiring panel
Circuit breaker, IEC, 3 pole, mounted in tower panel
Voltage regulator (single phase sensing)
Tower panel, IP22, bottom cable entry

Mechanical governing system

Lubricating oil
Oil drain line with valve

Includes lifting provisions and termination points for coolant
Captive linear vibration isolators between base and engine-generator

12 Volt battery with rack and cables

Engine and alternator pre-paint, Caterpillar yellow

Optional Equipment:

Coastal insulation protection

European upgrade to STD set for CE certificate
Global certification for CIS

Padlockable breaker device
4 Pole Circuit breaker

Battery charger
Volt free contacts for common alarm
Volt free contacts for genset running
Emergency stop with key
GCCP 1.3

Coolant heater

Single point lift for enclosure
Sound attenuated enclosure (GALV)

Fuel transfer control
Base feet
1000 hr extended service interval
Skidbase for enclosures
Skidbase for open sets
DEFRA bunded fuel tank
Low fuel level alarm

Industrial silencer removal
Battery removal
Silencer installation kit

PGS Test report @ 1.0 power factor

Radiator stone guard
Packing case - canopied set
Packing case - compact set

What Our Customers Are Saying About Us

Gregory Poole Equipment Company

4.0

Based on 58 reviews

review us on

Tom Corona

21:51 06 May 26

Rich Stidd

22:10 02 May 26

Carlos Virgilio Sauceda Rivera

20:55 23 Mar 26

John Karpathian

16:21 24 Jan 26

Clean store and great employees

Hunter Flaugher

12:56 06 Aug 25

Hydraulic pump shop is unmatched. I made the mistake of going somewhere else before bringing my pump here. These guys were more than helpful and friendly. Went out of their way to help me find a solution for my problem even when it didn’t benefit them. This is how businesses should be run. I won’t go anywhere else.

Brian Hrudka

16:45 12 Feb 25

Too bad Poole Cat Field Service is better at invoicing than actually getting my machines moving.

A prompt and courteous technician arrived, and correctly diagnosed two problems with my mini Ex. Thank you. I corrected those problems, but machine still did not work.

He diagnosed a fuel problem as a clogged filter, rather than a bad fuel pump which I managed to diagnose. I also figured out, via help on the internet, that the fuel shut-off solenoid was bad.

Machine runs fine now. So my advice is to check the internet, before letting Poole charge you $870 for a two hour field visit. And you can find a perfectly fine aftermarket fuel pump for $20 rather than the $250 that Poole charges... and it arrives faster,

Jacey Price

21:04 05 Dec 24

Need to teach a tech how to drive a service truck. Around 2:48 on highway 40 east, the truck pictured (plate ending in 8236) flew across 3 lanes of traffic to meet the Cleveland rd exit. Almost hit a semi and caused me to swerve with my children in the car. Glad making the exit was more important than children’s lives.