CAREERS
(800) 451-7278

Contact us

Contacto
Request a Service Request New Equipment Request Used Equipment Request Rental Equipment
SEARCH

CALL US
CONTACT US
Request a Service Request New Equipment Request Used Equipment Request Rental Equipment
Menu

ATC Service Entrance Rated MCCB & Power Breaker Based ATS

  • Home
  • New Power
  • ATC Service Entrance Rated MCCB & Power Breaker Based ATS
    • Back to Home

    Cat® Service Entrance Rated (SER) automatic transfer switches (ATS) are designed to provide standby power emergency power to entire installation loads to protect against utility power interruption; yet allow the ATS to be as close as possible to the point of service entrance. By safely and in code compliance, integrating the necessary overcurrent protection and service disconnecting means into the automatic transfer switch, a single installation can be made at the service entrance. This design eliminates the need for a separate upstream fault protection and respective interconnections, which in turn reduces installation space, time, and cost. Breaker-based Service Entrance Rated transfer switches are available from 30A to 5000A.

    Pricing: Contact for Pricing

    Request a quote

    Cat® Service Entrance Rated (SER) automatic transfer switches (ATS) are designed to provide standby power emergency power to entire installation loads to protect against utility power interruption; yet allow the ATS to be as close as possible to the point of service entrance. By safely and in code compliance, integrating the necessary overcurrent protection and service disconnecting means into the automatic transfer switch, a single installation can be made at the service entrance. This design eliminates the need for a separate upstream fault protection and respective interconnections, which in turn reduces installation space, time, and cost. Breaker-based Service Entrance Rated transfer switches are available from 30A to 5000A.

    Pricing: Contact for Pricing

    Request a quote
    Rating Range 30-5000A
    Switch Type Molded Case and Power Breaker
    Transfer Type Open / Closed / Delayed
    Applicable Testing
    UL 1008 listed up to 3200A

    4000A, and 5000A UL 891 listed
    Drawout Power Breaker 200-5000A 2, 3, or 4-Pole
    Fixed Mount Power Breaker 200-3200A 2, 3, 4-Pole
    MCCB 30-1000A 2, 3, or 4 Pole
    System Voltage Application 120-600 Vac 50/60 Hz
    Withstand (Power Breaker) Up to 100 kAIC at 600V 3 cycles

    Standard Equipment:

    • Controls And Wiring
      • All controls relays and industrial grade relays are totally encapsulated to minimize exposure to dust and dirt. Lugs are 90º rated and all control wire is #16 AWG, type XLPE with a 125º temperature rating.
    • Enclosure
      • Durable powder-coated steel NEMA 1, 3R or 12 enclosures with three door hinges to ensure proper support of the door and door mounted devices. The hinges have removable hinge pins to facilitate door removal for easy wall mounting or service and are supplied with pad-lockable latches.

    Optional Equipment:

    • Available Options
      • 4-position test switch
      • Remote communications
      • Surge suppression
      • Selectable automatic or non-automatic operation
      • Seismic Zone 4 Qualified (BOCA, CBC, IBC, UBC and OSHPD)
      • Communications for the ATC-300+ controller via RS-232 or Modbus through an integrated RS-485 port
      • Field selectable, multi ratio, control voltage transformer 50/60 Hz
      • Load sequencing contacts
      • Multi-meter options available
      • Open, closed or delayed transition
      • Space heaters
      • Integral overcurrent protection
    • Optional Delayed Transition Includes:
      • Pre-transfer signal with 1 N.O. and 1 N.C. contacts
      • Time delay neutral
    Gregory Poole Equipment Company
    Gregory Poole Equipment Company
    3.9
    Based on 46 reviews
    powered by Google
    review us on
    Renee HerndonRenee Herndon
    21:55 29 Feb 24
    Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.
    Michael BirrenMichael Birren
    14:58 24 Feb 24
    I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.
    David LawrenceDavid Lawrence
    13:04 22 Feb 24
    Brandon PierceBrandon Pierce
    22:00 18 Feb 24
    Darin NoeDarin Noe
    01:17 16 Feb 24
    Jose SotoJose Soto
    15:26 23 Sep 23
    OLEKSANDR “Alex” KovalenkoOLEKSANDR “Alex” Kovalenko
    14:27 18 Sep 23
    👍
    Hunter ElliottHunter Elliott
    16:17 07 Sep 23
    Rick Kelly-CrapseRick Kelly-Crapse
    21:06 25 Aug 23
    They had all my parts for my 3208 Cat.Friendly folks at parts counter.
    js_loader

    Contact Us Today

    Get In Touch
    Call: (800) 451-7278