7495 HD Electric Rope Shovel

Back to Home

Cat® Electric Rope Shovels combine immense payload capability with low maintenance requirements and high reliability to deliver the lowest cost-per-ton loading solution for long-life mines. The Cat 7495 HD is a smaller, tougher version of the 7495. Like the 7495, it features AC IGBT electrics for greater uptime, lower operating costs and faster cycle times. The 7495 HD is cleaner and more efficient than diesel-powered machines, plus its regenerative braking technology feeds electrical energy back to the grid.

Request a quote
Dipper Capacity 27.5-60.4 m3 (36-79 yd3)
Dipper Payload 90t
Note Dependent on application and material density.
Ballast - Furnished By Customer 574000lb
Note (1) These weights will vary slightly depending upon dipper and optional equipment selection.
Note (2) All specifications are based on a 32 m3 (42 yd3) dipper and standard 213.4 cm (84 in) treads.
Working Weight - With Dipper and Standard Links 2856700lb
Cutting Height - Maximum 48.75ft
Cutting Radius - Maximum 74.75ft
Dumping Height - With Clearance to Open Dipper Door 30.84ft
Note (1) Optimal working ranges based on loading a Cat® 793F truck.
Note (2) *All specifications are based on a 32 m3 (42 yd3) dipper and standard 213.4 cm (84 in) treads.
Radius of Level Floor 52.49ft
Revolving Frame Tail Swing Radius 30.51ft
Components (1) 6 pumps (4 for open gear lubricant and 2 for grease) located in an insulated, heated, double-walled lube room.
Components (2) External fastfill from lower level.
Type Automatic, single-line system for open gear lubricant and grease.
Drive IGBT Acutrol drive system.
Note Other voltage options available to suit customer requirements.
Power Requirements - 50 Hz 6,000V, 6,600V, 7,200V, 11,000V
Power Requirements - 60 Hz 7,200V
Power Requirements - Average Power Demand 832-1165 kW (1,116-1,562 hp)
Power Requirements - Peak power 4466HP
Power Requirements - Voltage 3 phase, 50/60 Hz, 7,200V
Components One piece, forged, seamless tubular dipper handle and wide-spread boom point sheaves equipped with hoist ropes and dipper padlocks to stabilize dipper handle.
Crowd Rope Crowd: the crowd machinery is located at the front center of the revolving frame; consisting of a motor, brake, drum and gearing. Plastic-impregnated crowd and retract ropes are used to move the dipper handle fore and aft.
Rope Data - Boom Suspension - Diameter 3.25in
Rope Data - Boom Suspension - No. 4
Rope Data - Crowd - Diameter 2.5in
Rope Data - Crowd - No. 1
Rope Data - Dipper Trip - Diameter 0.625in
Rope Data - Dipper Trip - No. 1
Rope Data - Hoist - Diameter 2.75in
Rope Data - Hoist - No. 2
Rope Data - Note High impact ropes available as an option.
Rope Data - Retract - Diameter 2.5in
Rope Data - Retract - No. 1
Crawler Dimensions - Overall Width 213.4 cm (84 in) Treads, Standard 32.75ft
Crawler Dimensions - Overall Width 274.3 cm (108 in) Treads 34.75ft
Ground Bearing Pressure Ground bearing pressure is dependent upon many factors.
Ground Bearing Pressure - 213.4 cm (84 in) Treads - Standard 58psi
Ground Bearing Pressure - 274.3 cm (108 in) Treads 46psi
Ground Bearing Pressure - Total Effective Bearing Area (1) 343ft²
Ground Bearing Pressure - Total Effective Bearing Area (2) 442ft²
Hoist A planetary gearbox with dual-output pinions provides the hoist torque transfer from the electric motor to the hoist drum gear.
Planetary Propel Dual-motor independent drive.
Swing Two planetary gearboxes, each driven by a vertically mounted motor, are located on either side of the revolving frame. Dual-output pinion shafts from each gearbox engage the swing rack.
Upper Works Overall Width - Including Standard Walkways 44.25ft

Coming Soon

Renee HerndonRenee Herndon
21:55 29 Feb 24
Dalton was very helpful, The road construction, however, was not! 😂I would rather have to sand paper an alligators @$$ in a phone booth that to get in that mess again.
Michael BirrenMichael Birren
14:58 24 Feb 24
I purchased a used C-15 from a customer of Greg Pool was a running take out. I picked up the engine from the Greg Pool Cat near Nags Head NC. They started they had done all service on this engine stated the hours and all items replaced during the life of engine under their care. I just recently put the engine in my boat after 2 years of building the vessel I find that everything they said about the engine was a LIE!!! Turbo was Bad, After cooler was not updated to the newer version for the C-15 it was missing a terminal Resistor that was clearly stolen off the engine which created a major issue with start up upon installation. Greg Pool Caterpillar stated the hours at 3300 we find out there were 5700 hours. I didn’t do a start up or test run which I regret because i was dealing with a Caterpillar dealer i thought i could trust them. Clearly not Buyers Be Ware if your dealing with Greg Pool Caterpillar in NC. I have 3 of the C-15 engines in my Work boats here in Tampa Fl and my Cat dealership here is Ring power who have done an amazing job to get me going with this Engine. I am very Disappointed in The Caterpillar company for allowing such A dealership to exist.
David LawrenceDavid Lawrence
13:04 22 Feb 24
Brandon PierceBrandon Pierce
22:00 18 Feb 24
Darin NoeDarin Noe
01:17 16 Feb 24
Jose SotoJose Soto
15:26 23 Sep 23
Hunter ElliottHunter Elliott
16:17 07 Sep 23
Rick Kelly-CrapseRick Kelly-Crapse
21:06 25 Aug 23
They had all my parts for my 3208 Cat.Friendly folks at parts counter.
js_loader