Cat C32 Generator Set (US EPA Tier 4 / IMO III)
Generator Set Specifications
- Minimum Rating
-
282 ekW
- Maximum Rating
-
940 ekW
- Frequency
-
60hz
Engine Specifications
- Configuration
-
Vee-12, 4-stroke-Cycle-Diesel
- Aspiration
-
Turbocharged-aftercooled aspiration
- Bore
-
5.71in
- Stroke
-
6.38in
- Displacement
-
1959in³
- Emissions
-
U.S. EPA Tier 4 Final certified / IMO III emissions certified (SCR required)
- Rated Engine Speed
-
1800 rpm
- Generator
-
SR5 - Form Wound
- Governor
-
Electronic (A5 ECM)
- Cooling
-
Heat exchanger, keel or radiator cooled
- Oil Change Interval
-
750 hrs
- Refill Capacity
-
Lube Oil System w/ oil filter change: 146 L (38.5 gal)
Generator Set Dimensions
- Length
-
167.2 in/4245 mm (minimum), 226.1 in/5742 mm (maximum)
- Width
-
59.9 in/1521 mm (minimum), 89.8 in/2280 mm (maximum)
- Height
-
70.4 in/1747 mm (minimum), 92.8 in/2356 mm (maximum)
- Engine Dry Weight
-
15721 lb/7131 kg (minimum), 21998 lb/9978 kg (maximum)
Clean Emissions Module (CEM) - Dimensions
- 6 Brick Z-Flow - Length
-
147.7in
- Dosing Cabinet - Weight
-
209lb
- 6 Brick Z-Flow - Weight
-
1246lb
- 6 Brick U-Flow - Weight
-
1235lb
- Dosing Cabinet - Height
-
22.8in
- 6 Brick U-Flow - Width
-
56.9in
- 6 Brick U-Flow - Length
-
85in
- Dosing Cabinet - Width
-
18.8in
- 6 Brick Z-Flow - Width
-
43.5in
- 6 Brick U-Flow - Height
-
23.5in
- Dosing Cabinet - Length
-
37.4in
- 6 Brick Z-Flow - Height
-
23.5in
Standard Equipment:
-
- Air Inlet System
-
- Separate circuit aftercooled (SCAC)
- Closed crankcase fumes disposal
-
- Control System
-
-
- Cooling System
-
- Heat exchanger or Keel Cooling
- Watercooled exhaust manifold and turbocharger
- Hard seawater lines – no flexible hoses
- Flanges for cooling connections, ANSI or DIN
-
- Fuel System
-
- Duplex fuel filters with hybrid fuel lines
- Primary fuel filter with water separator installed on base frame
-
- Generators And Generator Attachments
-
- IP23, air cooled, form wound SR5 generator offered in 440, 480 and 690V
-
- Lube System
-
- Oil fill, simplex filter and dipstick
-
- Mounting System
-
- Helical spring/rubber isolated mounting for vibration and structure borne noise reduction
-
- General
-
- Right or left hand service sides
- Customer wiring and service tool connector
Optional Equipment:
-
- Alarm And Protection
-
- MGCP III B control panel with Cat® Alarm and Protection System
- IP44 generator protection
-
- Exhaust System
-
- Muffler
- Water-in-fuel and exhaust temperature sensors
- SOLAS approved spray shielding
-
- Charging System
-
-
- Fuel System
-
- Manual or electric fuel priming pump
- Fuel cooler
-
- Lube System
-
-
- Starting System
-
- Starting motors – air, electric or redundant
