| Potencia de la base (1er engranaje) - Red | 238HP |
|---|---|
| Bore | 5.1in |
| Desplazamiento | 763 pulgadas... |
| Emisiones | Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent |
| Modelo de motor | Gato C13 |
| Maximum Altitude - Full Power | 13900ft |
| Maximum Altitude - Full Power (Tier 2) | 12049ft |
| Maximum Altitude - Full Power (Tier 3) | 14349ft |
| Par máximo - VHP Plus | 1137lb/ft |
| Nota (1) | Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. |
| Nota (2) | Optimized VHP Plus is standard for the 14M3. |
| Nota (3) | Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. |
| Nota (4) | Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp) |
| Note (5) | Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
| Número de cilindros | 6 |
| Velocidad a la potencia nominal | 1,850 rpm |
| Standard - Fan Speed - Maximum | 1,600 rpm |
| Standard - Fan Speed - Minimum | 550 rpm |
| Capacidad estándar | 122°F |
| Golpe | 6.2in |
| Aumento del par de torsión | 41% |
| Gross Vehicle Weight - Base* - Front Axle | 13994lb |
|---|---|
| Gross Vehicle Weight - Base* - Rear Axle | 36994lb |
| Gross Vehicle Weight - Base* - Total | 50980lb |
| Gross Vehicle Weight - Typically Equipped - Front Axle | 15245lb |
| Gross Vehicle Weight - Typically Equipped - Rear Axle | 42005lb |
| Gross Vehicle Weight - Typically Equipped - Total | 57250lb |
| Nota | *Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab. |
| Peso operativo - Típicamente equipado | 57250lb |
| Radio del arco | 16.3in |
|---|---|
| Blade Height - With Cutting Edge | 24.9in |
| Blade Height - Without Cutting Edge | 23in |
| Ancho de la hoja | 14 pies |
| Blade Width - With End Bits | 169in |
| Blade Width - Without End Bits | 164in |
| Despeje de la garganta | 4.6in |
| Rango de la punta de la hoja - Hacia atrás | 5° |
|---|---|
| Alcance de la punta de la hoja - Adelante | 40° |
| Círculo de cambio de centro - Izquierda | 25.6in |
| Círculo de cambio de centro - Derecha | 20.5in |
| Profundidad máxima de corte | 23.3in |
| Elevación máxima sobre el suelo | 16.5in |
| Máximo alcance del hombro fuera de los neumáticos - Izquierda | 73.6in |
| Máximo alcance del hombro fuera de los neumáticos - derecha | 78.9in |
| Desplazamiento lateral del tablero - Izquierda | 29.1in |
| Desplazamiento lateral del tablero - Derecha | 31.1in |
| Circle - Outer Diameter | 71.7in |
|---|---|
| Eje delantero - Oscilación total por lado | 32° |
| Eje delantero - Rueda inclinada - Izquierda/Derecha | 17.1° |
| Circle Drive | 1.8gal (US) |
|---|---|
| Sistema de refrigeración | 15.9gal (US) |
| Diesel Exhaust Fluid Tank (Tier 4 Only) | 5.8gal (US) |
| Tanque de combustible | 109.9gal (US) |
| Sistema hidráulico | 33gal (US) |
| Transmission and Differential | 23.5gal (US) |
| Aire acondicionado | The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton). |
|---|
