Oil and Gas

Engine Specifications

Minimum Rating
800BHP
Maximum Rating
1500BHP
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100r/min
Bore
5.7in
Stroke
6.4in
Displacement
1953in³
Aspiration
Turbocharged-Aftercooled
Governor and Protection
ADEM A3
Engine Weight - Net Dry
5040lb
Oil Change Interval
250
Rotation from Flywheel End
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)

Capacity for Liquids

Minimum Cooling System - Engine Only
14.5gal (US)

Dimensions

Length
75.5in
Width
85in
Height
52in

Standard Equipment:

  • Air Inlet System
    • Quad turbocharger — 3 cylinder exhaust to each turbo
    • Connections configured for ATAAC (Air-to-Air-Aftercooled)or remote heat exchanger
  • Control System
    • ADEM A4 electronic control module
    • Electronic governing, PTO speed control
    • Customer programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Automatic fuel temperature compensation
    • Programmable low and high idle, and top engine speedlimit
    • Electronic diagnostics and fault logging
    • Engine monitoring system
    • SAE J1939 broadcast (diagnostic and engine status)
  • Cooling System
    • Gear-driven centrifugal jacket water pump — RH
    • Integrated thermostat and housing
    • Engine oil cooler
    • Optional installed transmission oil cooler
  • Exhaust System
    • Exhaust manifold — dry
    • Two vertical exhaust outlets (front and rear)
  • Fuel System
    • MEUI
    • Fuel priming pump
    • Fuel transfer pump
    • Primary and secondary fuel filter — RH configured forremote mounting (installed RH on shipping plate)
  • Flywheels And Flywheel Housing
    • SAE No. 0 or SAE No. 1 flywheel iron housing
    • SAE No. 0 or SAE No. 1 flywheel
    • Optional transmission adapter
  • Lube System
    • Crankcase breather
    • Oil filter — RH standard, optional LH or remote mountservice
    • Oil level gauge — RH standard, optional LH or dualservice
    • Oil filler — RH standard, optional LH or dual service
    • Shallow oil pan, rear sump
  • Mounting System
    • Trunnion front support
    • Vertical and horizontal pads on rear flywheel housing
  • Protection System
    • 24V electronic
    • Engine overspeed with optional air shut-offs withindicators
    • Low engine oil pressure
    • Fuel filter restriction
    • Fuel temperature
    • High engine coolant temperature
    • Low engine coolant temperature
  • General
    • Vibration damper and optional guard
    • Lifting eyes
    • Optional customer wiring connector
    • Service tool connector
    • Paint — Cat yellow

Optional Equipment:

  • Air Inlet System
    • Air cleaner
    • Air inlet adapters
    • Turbocharger outlet adapters
    • Air lines
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mounting
    • Circuit breakers and mountings
  • Cooling System
    • Dry charge coolant conditioners
    • Thermostat housing
    • Coolant level sensor
    • Radiator
    • Blower fans
    • Suction fans
    • Fan adapters
    • Fan drives
  • Emissions
    • IMO certifications
  • Exhaust System
    • Elbows
    • Mufflers
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Customer management device
    • Interconnect harness
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Oil service side
    • Oil level gauge
    • Oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front
    • Engine support — rear
  • Power Take-offs
    • Auxiliary drive
    • Damper pulley
    • Hydraulics gear pumps
  • Protection System
    • Mechanical shutoffs
    • Solenoid shutoffs
  • Starting System
    • Electric starting motors – 12V, 24V
    • Battery sets – 24V
    • Battery cable
    • Battery rack
    • Starting aids
  • Transmission Arrangement
    • Transmissions water lines
    • Transmissions cooler