Engine meets U.S. EPA Tier 4 Final/EU Stage IV emission standards.
Maximum Gross Torque - ISO 14396
369ft·lbf
Note
Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
Rated Net Power - DIN ISO 14396
114HP
Weights
Operating Weight
21082lb
Buckets
Bucket Capacities
1.3-1.9 m³ (1.7-2.5 yd³)
Bucket Capacities - General Purpose
1.3-1.9 m³ (1.7-2.5 yd³)
Service Refill Capacities
Transmission
0.9gal (US)
Diesel Exhaust Fluid (DEF) Tank
5gal (US)
Note
DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
Cooling System
5.7gal (US)
Engine Crankcase
2.3gal (US)
Fuel Tank
40.7gal (US)
Hydraulic System - Including Tank
25.9gal (US)
Axles - Front
4.5gal (US)
Axles - Rear
4.5gal (US)
Hydraulic Tank
14.5gal (US)
Cab
ROPS
SAE J1040 MAY94, ISO 3471-1994
FOPS
SAE J/ISO 3449 APR98, Level II, ISO 3449:2005 Level II
Note (3)
The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 103 dB(A).
Note (4)
*The measurements were conducted with the cab doors and windows closed.
Note (1)
Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
Note (2)
The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 77 dB(A).
Engine - Tier 4 Final/Stage IV
Maximum Net Torque - ISO 9249
365ft·lbf
Maximum Net Torque - SAE J1349
361ft·lbf
Steering
Steering Articulation Angle - Each Direction
40°
Maximum Flow - Steering Pump
21.7gal/min
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed
2.3s
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
3.4turns
Maximum Working Pressure - Steering Pump
3190psi
Loader Hydraulic System
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High
40gal/min
Relief Pressure - Tilt Cylinder
4641psi
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift
4.8s
Hydraulic Cycle Time - Dump, at Maximum Reach
1.8s
Hydraulic Cycle Time - Rackback
2.2s
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level
2.7s
Hydraulic Cycle Time - Total Cycle Time
11.5s
Maximum Flow - Implement Pump
43.6gal/min
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard
25gal/min
Maximum Flow - Implement Pump - 4rd Function, Maximum Flow
25gal/min
Maximum Working Pressure - Implement Pump
4061psi
Note
All cycle times listed are with cylinder snubbing turned off.
Relief Pressure - Tilt Cylinder - 3rd Function Relief Pressure
4641psi
Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure
4641psi
Transmission
Forward and Reverse - Low Range, Speed Range 1*
6.3mile/h
Forward and Reverse - High Range
25mile/h
Note
*Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.